The simple installation steps in this booklet to create a perfect base for tile or floor coverings. NOTE: Do not use USG Fiberock panels over concrete subfloors or over cushion-backed vinyl. Tools Common tools like those shown below are typically all that are needed to install USG Fiberock panels, though additional, specialized tools. 484 x 44 x 164 mm (19.06 x 1.73 x 6.46 ') Weight. 2.30 kg (5.07 lb) Networking Interfaces. Serial Console Port (1) RJ45 Serial Port: Data Ports (2) 10/100/1000 RJ45 Ports (2) 10/100/1000 RJ45/SFP Combination Ports: Max. Power Consumption. Internal AC/DC Power Adapter, 60W (24V, 2.5A) Supported Voltage. The IT Handbook provides guidelines, best practices and recommendations to be followed by each USG institution. The IT Handbook sets forth procedures that each USG participant organization must follow to meet both Board of Regents policy mandates and the statutory or regulatory requirements of the state of Georgia and the federal government.
Power Adapter (12V, 1A) |
Usg Drywall Installation Manual
Screws (Qty. 2) |
Usg Installation Manual
UniFi Controller System Requirements
Usg Policy Manual
- Microsoft Windows 8, Mac OS X, or Linux
- Java Runtime Environment 1.6 (or above)
- Web Browser: Mozilla Firefox, Google Chrome, Microsoft Edge, or Microsoft Internet Explorer 11
- UniFi Controller software v5.4 or higher (available at: ui.com/download/unifi)
Ports Panel
Console |
---|
RJ45 serial console port for CLI management. Use a RJ45-to-DB9 serial console cable to connect the Console port to your computer. Then configure using the following settings:
|
Reset |
Resets to factory defaults. The UniFi Gateway should be powered on. Press and hold the Reset button for about 10 seconds until the right LED on the WAN 2 / LAN 2 port starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the UniFi Gateway will automatically reboot. |
WAN 1 Port |
Supports 10/100/1000 Ethernet WAN connections. Default setting is DHCP client. |
LAN 1 Port |
Supports 10/100/1000 Ethernet LAN connections. Default setting is DHCP Server. |
WAN 2 / LAN 2 Port |
Supports 10/100/1000 Ethernet connections. Configure the port using the UniFi Gateway configuration interface. |
LEDs
Usg Durock Installation Manual
System LED | |
---|---|
Click here for detailed descriptions. | |
Power LED | |
Off | Power Off |
Green | Power On |
Speed/Link/Act LED | |
Off | No Link |
Amber | Link Established at 10/100 Mbps |
Amber Flashing | Link Activity at 10/100 Mbps |
Green | Link Established at 1000 Mbps |
Green Flashing | Link Activity at 1000 Mbps |
Usg Handbook
Wall-Mounting (Optional)
By default, the WAN port is set to DHCP so it can be assigned network settings by the service provider.To change the setting, connect a computer directly (or through a switch) to the LAN 1 port of the UniFi Gateway.
- From a web browser, go to https://setup.ui.com
- Enter your Username and Password. Click Sign In.
- In the Setup window, click Edit Configuration to configure the WAN port to DHCP,Static IP, or PPPoE.
Note: If the UniFi Gateway has not been adopted by a UniFi Controller, the login window will be skipped and the Setup window will appear. |
For information on using the UniFi Controller software, refer to the User Guide located on our website at: ui.com/download/unifi
USG | |
Dimensions | 135 x 135 x 28.3 mm (5.32 x 5.32 x 1.11') |
---|---|
Weight | 366 g (12.9 oz) |
Networking Interfaces | |
Serial Console Port | (1) RJ45 Serial Port |
Data Ports | (3) 10/100/1000 Ethernet Ports |
Max. Power Consumption | 7W |
Power Supply | 12VDC, 1A Power Adapter (Included) |
Supported Voltage Range | 9 to 24VDC |
LEDs | |
System | Status |
Serial Console Port | Power |
Data Ports | Speed/Link/Activity |
Layer 3 Forwarding Performance | |
Packet Size: 64 Bytes | 1,000,000 pps |
Packet Size: 512 Bytes or Larger | 3 Gbps (Line Rate) |
Processor | Dual-Core 500 MHz, MIPS64 with Hardware Acceleration for Packet Processing |
System Memory | 512 MB DDR2 RAM |
On-Board Flash Storage | 2 GB |
Rackmount | Yes |
Operating Temperature | -10 to 45° C (14 to 113° F) |
Operating Humidity | 10 to 90% Noncondensing |
Certifications | CE, FCC, IC |